ML8 Single-Phase Control Panel
Single-phase operating panel, that features a courtesy light and buttons.
It is an ideal panel for roller doors, leaf-folding, sliding, sectional, leaf up and over and folding doors.
The unit features a built in 868MHz radio receiver for use with handheld and wall mount transmitters.
There is also a connection for a plug in safety receiver. This can be used with the Radiosens3 impact detector system, or the Radioband3 system, allowing a wireless safety edge to be installed.
Additional information
| Weight | 1.5 kg |
- Control panel for 1 single phase motor
- Power supply/Max. Pow. 230V/1CV (0.75kW) or 1.2 kW engine
- Built in 868MHz radio receiver for wireless controls. High security rolling code, cannot be cloned. 30 codes, expandable by 500 and can be managed by the ASSISTANT system if required
- Expansion input for Radioband safety receiver card with a memory of up to 6 Radioband 3G safety transmitters or 1 Radiosens3 transmitter
- N.C Photocell input
- N.C Stop input
- N.O Start input
- Inputs can be configured to suit specific requirements prior to shipping
- Flashing and solid light outputs (clean contacts)
- Status indicator by means of ERROR LED
- Courtesy light & control buttons
- See datasheet and manual for more specific details
- 5 Year Warranty!
- Turn off the power. Swap the brown and black motor wires.
- Note: The door will revert to deadman if there is a fault with the radiosens/radioband or photocell. Press and hold the close button on the panel or remote, after a few seconds it will start to close.
- The LEDs above the inputs (IN1, IN2 & IN3) indicate whether the input is active. If the LED above IN1 is on, you have a problem with the photocell circuit. If the LED above IN3 is on, you have a problem with the stop button circuit.
- If IN1 is on, check the photocell is clean, aligned properly that the cables are undamaged. If no photocell is fitted, check the terminals are linked.
- If IN3 is on, check that the emergency stop button hasn’t been pressed and that the cable to it is undamaged. If no stop button is fitted, check the terminals are linked.
- If the door has been running a lot in a short period of time and the control panel is clicking when it receives an input, it is likely the motor thermal cutout. Wait half an hour and try again. This is not a problem with the control panel.
- If the control panel is clicking when a remote or button is pressed, check the motor wiring and condition.
- The LEDs above the inputs (IN1, IN2 & IN3) indicate whether the input is active. If the LED above IN3 is on, you have a problem with the stop button circuit.
- If IN3 is on, check that the emergency stop button hasn’t been pressed and that the cable to it is undamaged. If no stop button is fitted, check the terminals are linked.
- If the door has been running a lot in a short period of time and the control panel is clicking when it receives an input, it is likely the motor thermal cutout. Wait half an hour and try again. This is not a problem with the control panel.
- If the control panel is clicking when a remote or button is pressed, check the motor wiring and condition.
Handheld transmitters: MUV2-HP, MUV4-HP
Wall transmitters (compatible in deadman or automatic closing): GO-BUTTON, GO-SWITCH
Wall transmitters (only compatible in automatic closing with safety): GO-PUSH2, GO-KEY, KEEPAD, KEEPUSH
Smartphone opener: SESAME
Wireless safety edge: RSEC3, RB3 TGL868 (See ML8 RB3 KIT) OSE-S 7502, Any resistive safety edge
To hardwire a safety edge, please contact us before ordering as we will need to configure an input before shipping.
Safety photocells: CP-PC180, CP-PC180B, CP-PC180AV, CP-PC180B-AV, IR8000
